Expert Answers about Chrysler Town and Country

• Hitch Recommendations for 2005 Chrysler Town and Country w/ Stow and Go Seats
• When you search by vehicle, the page you'll be taken to has a drop down menu at the top where you can choose Town and Country models 'with Stow-N-Go seats' or 'without Stow-N-Go seats'. The Draw-Tite Class III receiver hitch, part # 75305 would make a good choice. The hitch is indeed compatible with vehicles with stow-n-go seating. If you'll be using the hitch for towing, you'll need the following to complete your towing set-up: Trailer wiring harness with 4-pole trailer connector, part...
  view full answer...


• Wiring for Lights to Tow a 2006 Chrysler Town and Country on a Tow Dolly
• There are special wiring harnesses required for flat towing a vehicle. Regular trailer wiring harnesses like # 118300 are not designed to have power flow backwards through them and that would end up blowing the converter (on harnesses with converters) or damage the vehicle wiring and lights on harnesses that do not have converters. It looks like the 2006 Chrysler T and C has a 2-wire system (the turn signals are not separate from the brake lights). There are a couple of ways you can wire...
  view full answer...


• Is Front Timbren Kit Needed With Rear Kit for 2012 Chrysler Town and Country
• You do not have to use a front Timbren kit when installing the rear kit that fits your 2012 Chrysler Town and Country part # TDVRRT. Since you only need rear suspension support the front can be left alone and it'll be just fine.
  view full answer...


• Replacement Mounting Bracket for P3 Brake Controller
• We do have the replacement P3 mounting bracket part # TK5901 you are looking for.
  view full answer...


• Bracket Recommendation to Carry 4-Way Connector of Trailer Wiring Harness # C56333
• You can use the 4-way bracket part # 18144 to hold the 4-way connector of the Curt harness part # C56333. This would attach to the bottom of the rear bumper and would do a great job to hold the 4-way when not in use so that it's not dangling behind the vehicle. I attached a picture of this bracket installed in a similar way attached to a rear bumper.
  view full answer...


• Recommended Trailer Hitch and Wiring for 2016 Chrysler Town and Country with Stow-N-Go
• The etrailer Trailer Hitch Receiver part # e98854 is what I recommend for a 2016 Chrysler Town and Country which will work on models with Stow-N-Go seating. The etrailer hitch offers an easy bolt-on install, hidden crosstube, and durable matte finish which will all help provide a sleek/finished install look. In order to complete your towing setup you'll also need the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56331 which offers plug-n-play installation...
  view full answer...


• Hitch Recommendation for a 1999 Ford Windstar and a 2000 Chrysler Town and Country
• A hitch from a 2000 Chrysler Town and Country would not fit on a 1999 Ford Windstar. For the Town and Country you would want the part # 36296. For the Windstar you would want the part # 13085 . I attached install videos for both hitches to the right.
  view full answer...


• Can Test Wire be Put On Brake Output Circuit of Trailer Wiring
• If you wanted to use a jumper wire from a 12 volt power source like the positive terminal of a car battery you certainly could energize the circuit to test the brakes if you wanted to. We have 10 gauge wire sold as # 10-1-1 by the foot.
  view full answer...


• Curt Hitch that Fits 2005 Chrysler Town and Country
• We have Curt hitches that fit a 2005 Chrysler Town and Country like the part # 13389 for if you have the stow n go seats or the # C13362 if you do not but the # C13900 that you referenced does not fit.
  view full answer...


• Recommended Trailer Harness with 5 Wires to Power New Signal Lights
• For the functions you are needing on your trailer (ground, stop, two turn wires, running lights), it sounds like you are needing a wishbone 4-Way harness like the Optronics # A35W42B. This 4-Way flat connector has 5 wires, including separate wires for each of the stop/turn signals on the trailer. This particular harness measures 35 feet long and the ground (white) wire is 42 inches long. I have attached a couple of short video demonstrations on this product that you can also check out....
  view full answer...


• Ground Clearance at Rear of Vehicle after Hitch Install on a 2012 Chrysler Town and Country
• The Mopar hitch for your 2012 Chrysler Town and Country couldn't sit any higher than the Curt Hitch part # 13364 would as this hitch tucks right under the rear bumper. The # 13364 will give you about 12 inches of clearance, and since there is no way an OEM hitch could sit up any higher than this one this would be your best option since it is most likely less expensive.
  view full answer...


• Towing Capacities and Trailer Hitch/Wiring Recommendations for a 2005 Chrysler Town and Country
• There are a couple of weights to look at when determining how much trailer your 2005 Chrysler Town and Country can tow. First you need to consider the towing capacity of the vehicle itself or the gross trailer weight capacity listed for the vehicle. Additionally, Chrysler has a frontal area maximum that the trailer can have. They say that the front of the trailer cannot exceed 40 square feet. So if the trailer is 8 x 5 feet at the front or 10 x 4 feet, or any combination that adds up...
  view full answer...


• Trailer Wiring Harness Recommendation for a 2011 Chrysler Town and Country
• I almost always recommend Tow Ready wiring harnesses because we hear about less issues with them than with Curt harnesses, especially the ones that connect to the vehicle battery. For your 2011 Chrysler Town and Country I recommend harness # C56331. It even costs a little less. We have heard far less issues from our customers with the Tow Ready harnesses. It will install the same way as the Curt harness but I did link a video showing an installation for you. You would not have to run...
  view full answer...


• Recommended RV Cover For A Venture Sonic Lite 150VRB In Florida
• From the specs I've seen your Venture Sonic Lite 150VRB is 19'11" in length so I recommend the Adco Polypropylene Storage Lot RV Cover for Travel Trailer - Up To 20' Long - Tan Item # 290-74840. This cover works best for long-term storage in all climates. Heavy-duty, 4-layer fabric protects against UV rays, dirt, wind, and snow. Slip-seam strap system ensures snug fit and prevents damage from high winds and secures with cam buckles.
  view full answer...


• How to Install a Furrion Camera System on a Forest River RV Rockwood Geo Pro
• If your 2019 Forest River RV Rockwood Geo Pro is prewired for a Furrion RV Observation Camera System part # FOS43TASF then there should be a mounting bracket at the top of the trailer in which the camera would just plug into. If this is not the case then unfortunately you would need to test the tail light wires with a circuit tester as the manufacturer does not provides us with this information. The majority of factory installed systems will splice into the running light wire (usually brown)...
  view full answer...


• How to Make 6-Way Square to 7-Way Adapter
• To make a 7-way to 6-way square adapter will require you to get the part # 37995 to use the 6-way end and then wire up a 7-way to it like part # H20043. This will give you the adapter you would need since there isn't one already pre-made.
  view full answer...


• Recommended Trailer Fender for 2012 Little Guy Joey Trailer
• The Fulton Single Axle Trailer Fender with Top Step # F008563 referenced in your question does have extremely similar dimensions to the current fender on your Little Guy Joey Trailer. The fender measures 29-1/4 inches long, 9 inches wide, and 12 inches tall so it should work great as a replacement around your 13 inch tires. Customers usually use existing mounting brackets to install the new fenders but in your case I recommend adding some L-shaped brackets like # PF775-BKT-2. One end of...
  view full answer...


• Will Thule Roof Cargo Box TH859XT Fit a 2014 Chrysler Town and Country
• The extension for the part # TH859XT is the part # TH8591XT. To fit this on your 2014 Chrysler Town and Country would require you to have a roof rack with crossbars that are spread between 20" and 37" apart. lf this is the case, the extension will work just fine. I actually attached an install video that shows the # TH859XT installed on a 2014 Town and Country just like yours as well. In the video the van has the factory roof rack.
  view full answer...


• Easy to Install Brake Controller for 2015 Town and Country Platinum Unlimited w Factory 7-Way
• We don't have a vehicle specific brake controller install harness for your 2015 Chrysler Town and Country but based on what you described having you do have a really easy option for installing a brake controller since you said you wanted very clean and simple. The wire that's ran from the battery to back near the 7-way take and connect the one end to the vehicle's positive battery post and then connect the other end to the 1:00 pin position of your 7-way. With just those connections made...
  view full answer...


• Recommended Transmission Cooler For 2011 Chrysler Town And Country
• We have a few transmission coolers that are designed to fit your 2010 Chrysler Town And Country. The Derale Transmission Cooler, part # D13502 is a plate-fin cooler that may be just what you are looking for. The biggest concern when installing coolers is the location and whether there is room for the installation. This cooler measures 11 inches wide x 7-1/4 inches tall x 7/8 inch deep. I have attached a drawing that shows the best location to mount a cooler. I have attached links to a...
  view full answer...